Here is some basic trouble shooting tips for new monitors:
- The picture does not appear
- Check to make sure the signal cable is firmly connected in the socket.
- Check to see if the computer system's power is ON.
- Check that the Brightness Control is at the appropriate position, not at the minimum.
- The Screen is not synchronized
- Check to make sure the signal cable is firmly connected in the socket.
- Check that the output level matches the input level of your computer.
- Make sure the signal timing of the computer system is within the specification of the monitor.
- The position of the screen is not in the center
- Adjust the H-Size, H-Phase or V-Size, V-Center controls.
- Check if the signal timing of the computer system is within the specification of the monitor.
- The screen is too bright or too dark
- Check if the Brightness or contrast control is at the appropriate position, not at the maximum or minimum.
- Check if the specified voltage is applied
- Check if the signal timing of the computer system is within the specification of the monitor.
- Especially, check the horizontal frequency.
- The screen is shaking
- Move all objects that emit a magnetic field, such as a motor or transformer, away from the monitor.
- Check if the specified voltage is applied.
- Check if the signal timing of the computer system is within the specification of the monitor.
Trouble Shooting Tips after Installing a New Hard Drive - (February - 2009)
- Basic Troubleshooting Tips after Installing a New Hard DriveBased on Seagate IDE hard drives.
- If you have installed your drive and it does not function properly, perform the following basic checks:Warning: Always turn off the computer before changing jumpers or unplugging cables and cards. Wear a ground strap or use other antistatic precautions while working on your computer or handling your drive.
- Verify compatibility. Verify that the host adapter and drive are appropriately matched to each other and to your computer. Refer to the relevant documentation for details.
- Check all cards. Verify that all cards are seated in their slots on the motherboard and secured with mounting screws.
- Check all connectors and cables. Make sure all ribbon and power cables are securely connected. Ribbon cables are easily damaged, especially at the connector. Try a new cable that you know is good. Make sure no connector pins are bent. Verify that pin 1 on the interface cable is aligned with pin 1 on the drive and host adapter (see Figure 2 on page 6).
- Verify jumper settings. Review the instructions in this guide and in your host adapter installation guide. Make sure all appropriate jumpers are installed or removed as necessary.
- Check your power-supply specifications. Each time you add a new device to your computer, make sure your computer’s internal power supply can support the total power demand. If necessary, consult your dealer for a new power supply.
- Verify the drive-type settings in the system setup program. The drive-type settings in the system BIOS must not exceed the physical specifications of your drive. Also, the settings must not exceed the limitations set by the operating system and BIOS.
- Check for viruses. Before you use someone else's diskette in your system for the first time, scan the diskette for viruses.
- After you install your new drive, your computer will not boot, and no error message appears on the screen.Check your computer manual or BIOS manufacturer to determine whether your BIOS supports drives that have more than 4,092 cylinders. If your system has this limitation, use the following procedure to configure your computer:
- Turn off your computer, open the case, and remove your new drive.CAUTION: To avoid electrostatic discharge damage to your computer or hard drive, make sure you are well grounded before touching the drive, cable, connector or jumpers.
- Move the jumper on the alternate-capacity jumper, as shown in Figure 6. This causes the drive to appear to your BIOS as having a 2.1-Gbyte capacity (4,092 cylinders, 16 heads, 63 sectors per track). You may need third-party partitioning software, such as Disk Manager, to achieve full capacity of the drive.
- Remount your drive in the computer and replace the computer cover.
- Insert a bootable system diskette into drive A and turn on the computer. It should boot from drive A and automatically detect the new drive as a 2.1 –G.byte drive.
- Insert your Disc Wizard diskette into drive A and type A:XDM. Then press ENTER. This runs the Disk Manager program.
- Follow the Disk Manager instructions to install the dynamic drive overlay and to partition and format your new drive to its full capacity.
- After Disk Manager is done, reboot your system. You should see the Disk Manager banner and be able to access the full capacity of your new drive.
- The screen remains blank when you power up the system.If the steps listed above do not remedy this problem, try the following:
- Make sure the monitor is plugged in and turned on.
- Check all cards.
- Make sure the video card is seated in its slot and secured with mounting screws.
- Turn off the computer and remove the drive host adapter. If the screen turns on after you reboot, the host adapter may be incompatible or defective. If so, see your dealer.
- The system does not recognize the drive.
- Check all cables.
- Make sure the power supply is adequate for system needs.
- Reboot the computer and listen to make sure the drive motor starts up. If the drive is very quiet, it may be difficult to hear its discs reach operating speed. If the drive motor does not start up, recheck all drive cables.
- Verify that for each drive, a drive-type is listed in the system setup program.
- Try rebooting your computer by pressing the CTRL, ALT and DELETE keys simultaneously. If the drive is recognized after you reboot the system, the computer BIOS test may be completing before the drive is ready.One solution is to slow the processor speed during startup. If your computer has a turbo switch, set it to slow speed before turning the computer on. If there is no turbo switch, you may be able to use keyboard commands; see your computer manual for details. After the computer is up and running, return the processor to the fast speed.Another solution is to warm-boot your computer after every power-on.
- Check for I/O address conflicts. To isolate the conflict, verify that the drive and host adapter are compatible with your computer. Turn off the computer and remove all the peripheral adapter cards except for the video card and host adapter. If the computer recognizes the drive when you reboot the computer, turn off the computer. Reinstall the other peripheral cards, one at a time, until the conflict reoccurs. After you have isolated the source of the address conflict, you can resolve the conflict by changing the 1/0 address of the peripheral that appears to cause the conflict.
- If Disk Manager has installed the DDO on your hard drive and you have booted directly from a diskette, the information in the boot record for the drive may not have been loaded. Make sure there is no diskette in drive A and reboot. If you want to boot from the diskette, follow the "Booting with a Diskette" instructions under "Advanced Disk Manager Options" on page 20.
- The dealer partitioned and formatted the drive for you in the store, but the drive does not respond when you install it.
- Reboot the computer and make sure the drive spins up.
- Check all cables.
- Make sure the power supply is adequate for system needs.
- Make sure the DOS or Windows version the dealer used to partition and format the drive is the same version you have installed in your computer. If it isn't, see your dealer.
- Verify the drive-type values in the system setup program. You must install the drive using the same drive-type values your dealer used to partition the drive.
- Check for 1/0 address conflicts between peripheral cards.
- Check for viruses.
- The system hangs in FDISK or fails to create or save the partition record.
- Check all cables.
- Your setup system diskette may be corrupted. Try using a backup diskette.
- Make the partitions smaller.
- Change the interrupt jumper setting on the host adapter.
- Some BIOS have a Track 0 protection feature that protects Track 0 from viruses. This may cause FDISK to hang the system. You must disable this feature in the system setup program before you can use FDISK. See your computer reference guide for assistance. Be sure to re-enable this important feature when FDISK is done.
- The system error message, "Drive not Ready," appears.
- Check all cable connections. Make sure pin 1 of the drive is connected to pin 1 of the hard-disc controller or host adapter.
- Make sure the power supply is adequate for system needs.
- Reboot the computer and make sure the drive spins up.
- The FDISK error message, "No Fixed Disk Present," appears.
- Make sure the power supply is adequate for system needs.
- Verify the drive-type values in the system setup program.
- Check for 1/0 address conflicts.
- The drive does not format to full capacity.
- Verify the drive-type values in the system setup program. One of the following problems may have occurred:
- The values may be set with an incorrect translation characteristic.
- You may have entered a parameter value that exceeds the physical capacity of the drive.
- You entered a translation characteristic that does not take full advantage of the drive's capacity.
- The drive's physical specifications exceed the translation limits imposed by the BIOS.CAUTION: If you change the drive-type values in the system setup program, you must partition and format the drive again. This erases data on the drive.
- If you have partitioned the drive into individual logical drives, you may need to make the partitions smaller to access the full drive capacity.
- If your computer supports LBA mode, you may need to enable LBA mode in the system setup program to access the full capacity of the drive. Refer to your computer's reference guide to find out how to enable LBA.
- Your computer may not support drives that have more than 4,092 cylinders. Follow the instructions on page 25 for After you install your new drive, your computer will not boot, and no error message appears on the screen.
- The DOS message "Disk Boot Failure," "Non-System Disk" or "No ROM Basic - SYSTEM HALTED" appears.
- Reinstall the DOS system files using the DOS SYS utility.
- Check all cables.
- Use FDISK to verify that the primary partition is active.
- Check for viruses.
- The system error message, "HDD controller failure" appears.
- Confirm the jumper settings on the drive.
- Verify the drive-type settings in the system setup program
Trouble Shooting Tips after Installing a New Video Card - (February - 2009)
The following troubleshooting tips may help if you experience problems.
- Check that the card is seated properly in its expansion slot. Some AGP cards have design flaws and are "well-known" to "pop out" during transportation. For PCI cards, if the problem still exists, try a difference PCI expansion slot.
- Ensure the display cable is securely fastened to the card's display connector.
- Make sure that the display and computer are plugged in and receiving power.
- If necessary, disable any built-in graphics capabilities on your motherboard. For more information, see your computer's manual.
- Make sure you selected the appropriate display device and graphics card when you installed your enhanced driver.
- If you have problems during start-up, start your computer in Safe Mode. In Windows 98, press the F8 key when "Starting Windows 98" appears; or, in Windows 98, press and hold the CTRL key until the Windows 98 Startup Menu appears on the screen. Then select the number for Safe Mode, and press Enter.
Troubleshooting Tips for a New Motherboard - (February - 2009)
More than 70% of all computer problems are related to cabling and connections. Ensure all cables are connected and connected firmly. IDE and floppy ribbon cables and power cables can often go loose. Ensure microprocessor, memory modules, and adapters such as video card are inserted correctly and didn't "pop-up" due to vibration.
System has no power at all. Power light does not illuminate, fan inside the power supply does not turn on, and indicator light on keyboard does not turn on.
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Power cable is unplugged. | Visually inspect power cable. | Make sure power cable is securely plugged in. |
Defective power cable. | Visual inspection, try another cable. | Replace cable. |
Power supply failure. | Power cable and wall socket are OK, but system is still dead. | Contact technical support |
Faulty wall outlet;circuit breaker or fuse blown. | Plug device into socket know to work and test. | Use different socket, repair outlet, reset circuit breaker or replace fuse. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Expansion card is partially dislodged from expansion slot on the motherboard. | Turn off computer. Take cover off system unit. | Using even pressure on both ends of the expansion card, press down firmly on expansion card. |
Defective floppy disk drive or tape drive. | Turn system off. | Contact Technical Support. |
Defective expansion card. | Turn computer off. | Make sure expansion card is secure in expansion socket. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Connector between hard drive and system board unplugged. | When attempting to run the FDISK utility described in the HARD DISK section of the manual you get a message, INVALID DRIVE SPECIFICATION. | Check cable running form disk to disk controller on the board. Make sure both ends are securely plugged in; check the drive type in the Standard CMOS Setup (in your motherboard manual). |
Damaged Hard Disk or Disk Controller. | Format hard disk; if unable to do so, the hard disk may be defective. | Contact Technical Support. |
Hard Disk directory or FAT is scrambled. | Run the FDISK program, format the hard drive(See HARD DRIVE section of manual). Copy your backup data back onto hard drive. | Backing up the hard drive is extremely important. All Hard Disks are capable of breaking down at any time. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Hard Disk boot program has been destroyed. | A number of causes could be behind this. | Back up data and applications files. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
A number of causes could be behind this. | Use a file by file backup instead of an image backup to backup the Hard Disk. | Back up any salvageable data. Then do a low level format, partition, and high level format of the hard drive( see Hard Disk section of your manual for instructions). Re-install all saved data when completed. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
The IBM PS/2 uses a different format than other computers. | IBM PS/2 disk format will not work in an AT type computer. | Format disk in the AT type computer insert disk into the IBM PS/2 and copy the files you wish. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
No power to monitor. | All or part of the system may be inoperable. The new card may work but a mouse or COM port may not work. | Change the interrupt or RAM address on the new expansion card. See the documentation that came with the new card in order to change pin settings. many expansion devices come with proprietary software that will assist you in doing this. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Incorrect information entered into the configuration (setup) program. | Check the configuration program. Replace any incorrect information. | Review system's equipment. Make sure correct information is in setup. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
No power to monitor. | Power connectors may be loose or not plugged in. | Check the power connectors to monitor and to system. Make sure monitor is connected to display card, change I/O address on network card if applicable. |
Monitor not connected to computer. |
| See instructions above. |
Network card I/O address conflict. |
| See instructions above. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Connector between hard drive and system board unplugged. | When attempting to run the FDISK utility described in the HARD DISK section of the manual you get a message, INVALID DRIVE SPECIFICATION. | Check cable running form disk to disk controller on the board. Make sure both ends are securely plugged in; check the drive type in the Standard CMOS Setup (in your |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Memory problem, display card jumpers not set correctly. |
| Reboot computer. Re-install memory, make sure that all memory modules are installed in correct sockets. Check jumper and switch settings on display card. See display card section for information of settings. |
Computer virus. |
| Use anti-virus programs (McAfee/PC-cillin, E-port, etc) to detect and clean viruses. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Screen saver is enabled. |
| Disable screen saver. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Keyboard is disconnected. |
| Reconnect keyboard. Check keys again, if no improvement, replace keyboard. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Faulty Monitor. |
| If possible, connect monitor to another system. If no color, replace monitor. |
CMOS incorrectly set up. |
| Call technical support. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Floppy Drive cable not connected correctly. |
| Reconnect floppy cable making sure PIN1 on the Floppy Drive corresponds with PIN1 on floppy cable connector. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Bad floppy disk. |
| Try new floppy disk. |
Floppy disk not formatted |
| Format floppy disk(type ENTER) |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
SETUP program does not have correct information. |
| Boot from drive A: using DOS system disk. Input correct information to SETUP program. |
Hard Drive cable not connected properly. |
| Check Hard drive cable. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Master/Slave jumpers not set correctly. |
| Set master /Slave jumpers correctly. |
Hard Drives not compatible / different manufacturers. |
| Run SETUP program and select correct drive types. Call drive manufactures for compatibility with other drives. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
CMOS setup has been changed. |
| Run setup and select correct drive type. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Keys jammed or defective. |
| Replace keyboard. |
PROBABLE CAUSE | DIAGNOSIS | SOLUTION |
Keyboard is locked. |
| Unlock keyboard |
Troubleshooting Tips for a New Network Card - (February - 2009)
- If you can't connect to a server or if Windows reports an error after you double-click Network Neighborhood, try the following first:
- Make sure you're using the drivers that are on the driver’s disk that ships with the network interface card (NIC).
- Make sure the driver is loaded and the protocols are bound. Check the Device Properties list for trouble indicators (an "X" or "!" symbol).
- Test the NIC adapter with the diagnostic utilities that often came with the driver installation.
- Check with your LAN administrator - you may need to install additional networking software.
- If the problem persists, follow these guidelines:
- Make sure the cable is installed properly. The network cable must be securely attached at both RJ45 connections (adapter and hub). The maximum allowable distance from adapter to hub is 100 meters. If the cable is attached and the distance is within acceptable limits but the problem persists, try a different cable. If you're directly connecting two computers without a hub or switch, use a crossover cable.
- Try another network cable.
- Check the LED Lights on the NIC. Before the LEDs can be used for troubleshooting, the network interface card (NIC) must be connected to the network and the network driver must be installed. Most NICs come with LEDs near the connection. The meaning of the LED signals may be different from one manufacturer to the other. Here is a common LED description for 3COM 10/100BT dual speed NIC. Please consult your NIC manual for any difference.
LED | Description | Flashing | Steady (On) | Off |
10 LNK | Green: Link integrity | Reversed polarity | Good 10BT connection | No connection between NIC & hub |
100 LNK | Green: Link integrity | Reversed polarity | Good 100BT connection | No connection between NIC & hub |
ACT | Yellow: Port traffic for either speed | Network traffic present | Heavy network traffic | No traffic |
- The computer hangs when the drivers are loaded.
- Change the PCI BIOS interrupt settings. See your NIC and system manuals for more details.
- If you are using EMM386, it must be version 4.49 or newer.
- Diagnostics pass, but the connection fails or errors occur.
- At 100BT, use Category 5 wiring and make sure that the network cable is securely attached.
- At 100BT, connect to a 100BT hub/switch (not 100Base-T4).
- For NetWare, make sure you specify the correct frame type in your NET.CFG file.
- Make sure the duplex mode setting on the adapter matches the setting on the switch.
- The LNK LED doesn't light.
- Make sure you've loaded the network drivers.
- Check all connections at the adapter and the hub/switch.
- Try another port on the hub/switch.
- Make sure the duplex mode setting on the adapter matches the setting on the hub/switch.
- Make sure you have the correct type of cable between the adapter and the hub. 100Base-TX requires two pairs. Some hubs require a crossover cable while others require a straight-through cable.
- The ACT LED doesn't light.
- Make sure you've loaded the correct network drivers.
- The network may be idle. Try accessing a server.
- The adapter isn't transmitting or receiving data. Try another adapter.
- Make sure you're using two-pair cable for TX wiring.
- The adapter stopped working without apparent cause.
- Run the diagnostics program that came with the NIC.
- Try reseating the NIC in its slot, or try a different slot if necessary.
- The network driver files may be corrupt or missing. Remove the drivers and then reinstall them.
- The Wake on LAN (WOL) feature is not working.
- Make sure the WOL cable is attached and that power is being applied to the computer.
- Check the BIOS for its WOL setting. Some computers may need to be configured for WOL.
- Make sure the network cable is fully attached to the adapter.
- Crossover cable troubleshooting tips. When you work with network cabling, concentrators (hubs or switch), and NICs from different venders, it is possible to connect everything and still have no communication between file servers and workstations.When there are several unknown variables, it is difficult to determine which component is broken. Use these tips to isolate the problem.
- Determine whether your equipment complies with the 10Base-T or 100Base-TX standard. This is particularly important for hubs and switches.
- Connect a straight-through cable from the PC to the hub. The hub performs an internal crossover so that the signal can go from TD+ to RD+ and TD- to RD- (see How to Make Network Cables). When you look at an RJ-45 connector from the front, pin 1 is identified on the left-hand side when the metal contacts are facing up.
- Make sure that the TD+ and TD- wires are twisted together, and that the RD+ and RD- wires are twisted together. Using wires from opposing pairs can cause signals to be lost. For a 100Base-TX cable, pins #1 and #2 , and #3 and #6 must be on the same twisted strand.
- When there is doubt whether a hub is performing correctly, or if the impedance settings are in question, a crossover cable can help you isolate the failing component:
- Connect a file server and a client PC back to back with a crossover cable to verify that the NIC and network operating system are properly configured.
- To make a crossover cable, simple connect TD+ to RD+ and TD- to RD-. The cable performs the crossover that is usually performed by the hub. Make sure that two twisted-pair wires are used. If the file server and client PC function together as a small network, then either the existing cabling or the hub is the problem.
- If there is a proper crossover, the appropriate LED comes on. If there is a straight-through connection, the LED does not light. A blinking LED indicates that there is a polarity mismatch (that is, TD+ to RD- instead of TD+ to RD+).
Troubleshooting Tips for a New Sound Card - (February - 2009)
- Microsoft Volume Control or your mixer program mute options and volume sliders.
- Connect headphones to the stereo phone jack on your CD-ROM drive’s front panel; adjust the volume control settings on the drive. If there is sound from your headphones, check the CD audio cable connection from the CD-ROM drive to the audio card.
- Ensure the speakers are properly connected to the audio card’s output connector.
- Find out where to purchase quality discount computer speakers . Browse from the variety of models and designs.
- The audio card joystick port conflicts with another joystick port in the system. Disable the audio card joystick port, and use the system’s joystick port.
- The joystick drivers, MSJSTICK.DRV and VJOYD.VXD, may not be installed. Uninstall the joystick, then reinstall to load the drivers. The drivers should come with the driver CD or floppy diskette with your sound card.
- A hardware conflict with another device in your system.
- Previously installed sound card hardware or software needs to be removed.
- The audio card is not seated in the slot properly.
- PCI bus mastering devices may be interfering with the operation of the audio card. Temporarily remove non-essential PCI bus mastering devices.
- Right-click the My Computer icon on your desktop, and select Properties. The System Properties dialog appears.
- Click the Device Manager tab. In the Device Manager, a plus sign(+) represents an expandable list of items. A minus sign (-) represents an expanded list. A circled exclamation mark denotes a conflict.
- Double-click Sound, video, game controllers. A list of multimedia devices appears.
- Select your audio card.
- Choose the Properties button.
- Click the Resources tab.
- Uncheck the Use automatic settings option.
- Change "Settings based on:" if alternate settings are available.
- Determine the conflict by reviewing the "Conflicting device list".
- Select the conflicting item in the "Resource Settings" list.
- Click the Change Settings button.
- Use the mouse to select a new setting.
- Select OK to close each of the properties windows, and restart your computer.
- Click "Start" on the taskbar, and select Settings from the Start menu.
- Select Control Panel. The Control Panel group appears.
- Double-click the Add New Hardware icon. The Add New Hardware Wizard dialog appears.
- Select Next to continue.
- Choose Yes to have Windows search for new hardware, then select Next
- Select Next to continue.
- Select Finish, and follow the prompts to complete the new hardware installation.
- Right-click the My Computer icon on your desktop, and select Properties. The System Properties dialog appears.
- Click the Device Manager tab. A list of devices appears.
- Double-click CD-ROM, and select your CD-ROM drive.
- Choose the Properties button. The CD-ROM drive properties dialog appears.
- Choose the Settings tab.
- Click the "Auto insert notification" option to enable.
- Select OK until all Properties dialogs are closed, and restart Windows for the changes to take effect.
- Check the Microsoft Volume Control or the Audio Mixer Program mute options and volume sliders.
- Ensure the speakers are properly connected to the audio card’s output connector.
- Check the volume control and power connection of the speakers, if they are amplified. (Refer to the speakers documentation for detailed information).
- Ensure a hardware conflict does not exist between your audio card and another device in your system.
- PCI bus mastering devices may be interfering with the operation of the audio card. Temporarily remove non-essential PCI bus mastering devices. If the device is a display card, upgrade the display card drivers, or set the card to the default Windows VGA mode.
- Try different resource settings for the audio card, or set the card to use low DMA.
- Move the audio card to another PCI slot. Feedback from the power supply or another device may be responsible.
Troubleshooting Tips for Cases and Power Supplies - (February - 2009)
The most important part of a computer case is its power supply. Unfortunately, it's also the part that has most of the problems for a case. There are two situations when a new power supply may appear dead on arrival (DOA) when they are actually working as described below:
Most cases and power supplies these days are made and tested in China and other Asian countries where 220V electricity is used. Desktop computer power supplies do not switch the power voltage automatically. (Most notebook computers do!) If the factory forgets to turn the manual switch back to 110V for the North American market after testing, the power supply would appear DEAD if you use on a 110V-outlet. Therefore, always check the voltage setting on the back of a new power supply FIRST if it appears dead.
Do not expect an ATX power supply to work by simply plugging the power and turning on the switch. ATX power supplies are soft-switched on and off by the motherboard and BIOS. Therefore, you must plug it to a working motherboard with a working microprocessor, memory and video card to work. If your computer does not turn on after you turn on the power switch, it may not necessarily mean a dead power supply. The problem might be with the motherboard, microprocessor, memory or video card instead. You must examine all these components to isolate the problem.
The most effective technique to tell if a power supply is causing any problem is to use a different one to see if it solves the problem. If everything works with a different power supply, then the new power supply is most likely the troublemaker. Alternatively, you can plug the new power supply to an existing, working computer to see if it works there.
Computer cases are highly modular. If your computer case is still under warranty, you don't have to send the entire case back if only one part of it is defective. For instance, send only the power supply back for exchange if only power supply is dead. The same is true for the face panel and cover. This would save you quite a bit of shipping and sometimes downtime.
More than 70% of all computer problems are related to cabling and connections. Ensure that you all the power plugs are connected firmly, including power connections to your motherboard and all the drives.
Make sure the cooling fan inside the power supply is working all the time. Reach out to feel the fan behind your case often. Clean the fan if necessary. If your case feels warmer than room temperature, check the power supply fan first. Most power supply fans are difficult to replace. You are better off to replace the entire power supply since the new one comes with a brand-new warranty.
Before ATX form factor became popular, the compatibility between a power supply and a specific motherboard could be problematic. However, this problem nowadays does not happen very often any more.
The rest of a case is mostly mechanical. You should be able to find a way to get around most of the problems if you are mechanically inclined.
Fax/Modem Troubleshooting Tips - (February - 2009)
My modem is a 56K, but I can connect to the Internet only at slower speed.
The current copper wired telephone lines are limited only to about 53K. If you are connected only to 33.6 or 28.8K, check the following first:
- Is your modem compatible with the modem used at your ISP?
- Is your modem set up to run at full speed?
- What's the maximum speed your ISP allows?
- How far away are you from your ISP?
- Some modems need special initiation strings to get full speed.
- Some conditions are out of your control, such as weather and conditions of the telephone lines in your community.
- Problems may occur when you are dialing through a phone system such as one in a hotel.
- There may be an I/O conflict (see the solution for the previous problem).
- The Result Codes may have been disabled by the software configuration set up. Check if Q1 is in the configuration or initialization string. If so, change it to Q0.
- Your software may require numeric result codes rather than verbal result codes. Use either V0 for numeric result codes or V1 for verbal result codes in your initialization or configuration string.
- Some software require full extended result codes (i.e., CONNECT 33600 instead of CONNECT). This can be controlled by the Xn command. X0 sends a summarized code (CONNECT) and X4 sends a full extended code (CONNECT 33600)
Tips about DSL Modem - (February - 2009)
Digital DSL Modem
The modem that is used to send and receive data to and from a digital telephone line, for example ISDN and DSL modems. These modems send and receive the digital signals to and from the digital line. These modems are available in market with USB and Ethernet ports, for single computer the USB modem is the best choice but if you want to share one DSL connection on more than two computers then you should try Ethernet port modem. DSL modems use the digital signal that is why these modems do not convert the digital signals into analog. DSL modem provide higher speed internet up to 24 Mbps downstream and 3.5 Mbps upstream. The price range of DSL modems between 60$ to 225$ but Some DSL providers offer more benefits for you with DSL connection to compete with others services provider like free modem with one year warranty. If you want your DSL working with good speed and error free then make sure there is no any joint between telephone line tower and modem line. Your DSL modem may be heat up, hang and slow, if your DSL modem continually on for 24-hours, then restart it to solve this problem.
Suggested Reading
- What is DSL?
- DSL Availability
- DSL vs. Cable
- Cheap DSL Tips
- Choosing DSL Providers
- DSL Broadband
- DSL Filters
- DSL ISPs
- Direct TV DSL
- DSL Hardware
- DSL Reports
- DSL Speed Test
- Wireless Broadband
- DSL Internet Service
Wireless Router Tips - (February - 2009)
What to look for when buying a wireless router
There are a wide variety of wireless routers on the market today. The features you need will depend on the extent of your network. In general it is good to look for one that has a built in firewall for security, decent speed and the ability to act as both a wired and wireless router, and good range. Belkin routers and Linksys routers are two popular brands. For the best range and speed, look for a wireless router which uses 802.11g technology.
Sharing an internet connection with a wireless router
A wireless router hooks up directly to your cable or DSL modem via a cable. The wireless router will then transmit the broadband single to the computers with a wireless card in the range of the network. You will need to make sure that the cards are configured for the home network, same as with a wired network, but after that, you will be wire free!
Linksys wireless router
Linksys wireless routers are an excellent brand which offers many benefits to users. Linksys makes routers which use 802.11g technology, which offers increased speed and range over older standards. They offer wireless routers in a variety of price ranges so they are affordable and functional for a wide variety of wireless networks. You can also purchase a linksys router with speed booster technology to further increase network speed and productivity.
Wireless Router
A router is a device which connects one network to another. It is most used for connecting the internet (one large network) with a home or business network. Wireless routers allow you to share a broadband internet connection between several computers.
Wireless Router with Firewall
Not all wireless routers come equipped with a firewall, but it is worth investing in a router that has one. Linksys wireless routers come in a variety of prices with a variety of firewall capabilities. Depending on the security needs of your wireless network, you may want to consider getting a wireless router with sophisticated firewall technology.
Belkin wireless router
Belkin wireless routers offer excellent range and speed. One of their newest routers, the Belkin Pre-N has 8 times the range and 6 times the speed of regular 802.11g technology routers. They offer a variety of other wireless routers to meet the needs of small and large wireless network administrators.
Best Wireless Router
The best wireless router will depend on your wireless network. If you have a small network within a small range of one another, it may not be necessary to purchase the latest and greatest wireless router on the market. However, if you run an office or business and want to maintain quality speed and performance, it is in your best interest to purchase the latest technology for the wireless router.
Wireless Router Password
Most wireless routers come with a default password of admin. To maintain optimal wireless network security, it is a good idea to change this password so others will not be able to access the router, firewall, etc and hack your wireless network.
Wired and wireless router
Many wireless routers offer the ability to use both a wired and wireless network. If you are not ready, and cannot make the switch fully to a wireless network, consider purchasing a wireless router which offers both options.
Selecting a Scanner - (February - 2009)
Types of Scanners
Scanners come in a variety of configurations. The type you should consider depends on both your planned scanning needs and your budget.
- Drum scanners. This type of scanner provides the highest level of image quality. They are typically found at professional printing businesses. In a drum scanner, the original is attached to a cylindrical drum and rotated past the sensing elements. These scanners are very expensive, with capabilities that go well beyond the needs of desktop scanning.
- Flatbed scanners. This type of scanner provides a flat glass surface onto which the original is placed. The illumination and sensing elements move under the glass to scan the image. Flatbed scanners are available in a wide range of sizes, prices, and capabilities. Some flatbeds offer a transparency scanning adapter as an option.
- Single sheet scanners. This type of scanner is designed for single sheets of paper. You insert one edge of the paper in a slot and the scanner grabs it, feeds it past the sensing array, and passes it out the other side. Some single sheet scanners are even integrated into keyboards. Such scanners were originally designed for digitizing documents and images for archiving, and many models are not suitable for creating high-quality images.
- Sheet-fed scanners. These scanners take a stack of pages and scan them in sequence while you get coffee. Some even do duplex (2 sided) scans. They are very useful in some situations but not much use to the philatelist.
- Photo scanners. This type of scanner is designed to scan snapshots up to approximately 4´6 inches in size. Some are separate desktop units; others install directly into a computer much like a diskette drive.
- Hand scanners. This type of scanner requires the user to manually scan an image. Hand scanners look something like an overgrown mouse. To scan, you manually drag the unit over the original document. Handheld scanners are suitable only for small originals that are no wider than the scanner itself. In theory, most hand scanners permit you to scan a wide original in two or more passes and "stitch" the scans together into a final image. This, however, never works as well as the manufacturers claim.
- Slide scanners. This type of scanner is designed for scanning slides (transparencies) rather than opaque originals, such as photographic prints. While rarely relevant for scanning philatelic material, a dedicated slide scanner is the best choice for scanning slides. Some flatbed scanners come with transparency adapters but they do not provide top quality results, particularly with small slides such as 35mm. Slide scanners have very high resolution, typically a minimum of 2400 dpi, required for getting all the details out of your slides. Many slide scanners also have the ability to scan color negatives and to convert the negative image to a positive image.
For philatelic purposes, a flatbed scanner is undoubtedly the most versatile. You can scan anything from a single stamp to an entire stock book or album page. A hand scanner may be a viable alternative, particularly if your budget is tight. Their width limitation does not matter so much for stamps and covers. I have also seen single sheet scanners and photo scanners used successfully for philatelic purposes, although they require that the item being scanned be sandwiched between clear plastic sheets for feeding into the scanner.
Wireless Headset Tips - (February - 2009)
The Best Wireless Headset
The best wireless headset for you will depend on your needs and how often you will use it. For a cell phone wireless headset, you will want to look for a blue tooth headset, as that is the industry standard. Other features to consider include:
- Comfortable fit
- Features you require
- Within your price range
- Compatible with your current cell phone.
If you need a wireless headset with a landline telephone, you need to consider some alternate options:
- What brand name are you most comfortable with? Wireless headsets for your regular phone come from various manufacturers including Plantronics, GN Netcom and Polycom.
- How much desk space you want it to take up?
- How much range it needs to have (how large is your office)
You may not have considered it, but you can also get a headset for your computer. If you use Skype or any of the other nifty computer phone call programs, you may have a headset plugged into your desktop or laptop already, but wireless may make your life much more flexible.
Wireless Headset: Bluetooth
Bluetooth is another wireless standard, mostly used for short range connectivity. You will often find Bluetooth technology in printers, cell phones and wireless headsets. Its range is significantly shorter then other wireless technology, about 30 feet. It is less expensive then other Wi-Fi standards and works well for many home offices. This is why Bluetooth has been included in many wireless headsets - but beware of that range, you don't want to wander too far from your source and lose you call.
Reasons to Use a Wireless Headset
A wireless headset offers you significantly more freedom while you talk on your cell phone or regular phone. By plugging in the wireless adaptor, you can walk all over your home or office. The benefits in an office environment are clear, but these are also great for stay at home parents who may be chasing an active toddler all over the house! The car is another obvious location for the use of a wireless headset.
Good wireless headsets come equipped with volume control and answer buttons and they should be small and fit comfortably over your ear. They should be snug enough so you don't have to worry about the headset slipping off your ear or falling to the ground.
Problems with Wireless Headset
If your wireless headset is having performance issues, there are a few things you can check.
- Make sure your telephone or ell phone is within range and not overly obstructed.
- Check to make sure your cell phone battery is charged and you are receiving a good signal.
- Typically, with wireless headsets you will have multiple channels from which to select the best signal, so make sure that you have switched around to see which is best and that you aren't still on the default channel.
- Make sure you try your phone without the headset on at all to ensure that the line or signal is strong.
- Finally, check to make sure the batteries in the wireless headset are charged.
Wireless Headset
A wireless headset is a small device you slip over your ear that allows you to talk via your cell phone, but hands free. Using the blue tooth technology standard, wireless headsets offer an excellent range and great hands free features.
These wireless headsets have been especially popular with commuters and people who need to use their cell phones in their car. The increased safety afforded when you are using both hands to drive makes the investment in one of the headsets an easy decision. Additionally, you aren't hampered by an annoying cord which can also be hazardous if you need full range of motion to avoid a potential car accident.
Wireless Headset with Regular Phone
There are wireless headsets on the market that you can use with a regular phone, but don't think you'll have to buy a different headset for every phone in your home or office. There are also wireless headset devices that you can hook up to a regular phone, cell phone and PDA, and you can alternate which device you wish to use your wireless headset with. This kind of flexibility is key in this day and age of telecommunications - and for your wallet.
Post a Comment